call us on: +86 755 2733 5064  E-mail: wy@jiemeimould.com  
Jie Mei Precision Mould Ltd
Tel: +86 755 2733 5064
E-mail: wy@jiemeimould.com
Product Categories
News
Home > News > Content

Automotive Mould To Ensure The Quality Of Parts

Edit:Jie Mei Precision Mould Ltd   Date:Sep 28, 2017

The primary maintenance of the Automotive Mould refers to the operation of the Automotive Mould on the Automotive Mould and daily maintenance, the main content for the cleaning, lubrication and inspection.

 First, the Automotive Mould when the maintenance of the Automotive Mould before the Automotive Mould on the surface of the cleaning, to ensure that the Automotive Mould mounting surface and press work surface without crushing and Automotive Mould in the production of the parallel installation surface parallelism. After the Automotive Mould is installed, the Automotive Mould will be opened and the parts of the Automotive Mould will be wiped clean, especially the guide mechanism. For the surface Automotive Mould, the surface will be clean and clean to ensure the quality of the parts. The sliding parts of the Automotive Mould are lubricated and greased. Inspection of various parts of the Automotive Mould, especially the safety parts. Such as: safety side sales, safety screws, side guards, punching waste Road and so on.

Second, the production of maintenance in the production of regular parts of the Automotive Mould on the oil. Such as: pull the Automotive Mould of the material circle, rounded; trimming die of the knife-edge parts; flanging knife section and so on. Regularly clean up the waste of the small hole waste road of the trimming punching Automotive Mould. After the production of maintenance after the end of the Automotive Mould to conduct a comprehensive inspection. Automotive Mould a comprehensive cleaning, to ensure that the Automotive Mould cleanliness. The waste within the Automotive Mould clean up to ensure that no waste in the waste box. The use of the Automotive Mould and the use of the situation after the truth feedback to the Automotive Mould subpoena.

The secondary maintenance of the Automotive Mould refers to the regular maintenance of the Automotive Mould based on the technical state and complexity of the Automotive Mould. This maintenance work is done by the repair staff and is recorded according to the maintenance situation. The following describes the different requirements and methods of the two parts.

Pull the Automotive Mould punch, die: pull the Automotive Mould of the convex, concave die is the main problem is the hair and the surface of the pressure pit, the maintenance of the Automotive Mould when the fillet rough part of the polishing. If there is pressure to the Automotive Mould to repair welding, and then repair. Guide parts (guide column, guide sleeve and guide, etc.): Automotive Mould in the work will appear pull marks and so on. The main reason for the generation of lubricants is dirty and the guide gap is partial. Lead parts to produce pull marks to take the stone stone push after the way to eliminate the polished.

Saw blade: Automotive Mould in the course of the use of the blade edge prone to chipping and edge collapse phenomenon. At this point to die damage to the knife-edge repair welding repair

Springs and other flexible parts: the use of the process, the spring is one of the most vulnerable parts of the Automotive Mould, usually the phenomenon of fracture and deformation. The way to take is to replace, but the replacement process must pay attention to the spring specifications and models, spring specifications models through the color, diameter and length of the three to determine, only in the three cases are the same circumstances can be replaced.

Punch, punch sets: Automotive Mould used on the punch, punching most of the standard parts are used, the Automotive Mould in the course of the punch prone to break, bending and eating bad phenomenon. Punch sets are generally bite bad. Punch and punch the damage is generally the same specifications of the parts to be replaced. Punch the main parameters of the working part of the size, installation part of the size, length and size. Fastening parts: Check whether the fastening parts are loose or damaged. The way to do this is to change the parts of the same size. Binder and unloading parts: pressing parts such as pressing plate, gifted of plastic, such as unloading parts such as unloading board, pneumatic materials, such as the first device. Check the parts of the assembly relationship and whether the damage, the damaged part of the repair. Pneumatic top material to check whether the phenomenon of leakage, and the specific circumstances to take measures. Such as tracheal damage to replace and so on.


Contact Us
Address:No.172, Yanluo Road, Songgang Town, Bao'an District, Shenzhen City, China
Tel: +86 755 2733 5064  Fax:+86-755-27335065
E-mail:wy@jiemeimould.com
Copyright © Jie Mei Precision Mould Ltd